Please Login or Register
Translate: en_US
USD ( $ )
0Items in your cart
Cart Subtotal: $0.00
Click thumbnails to zoom & pan

Tobii-ATI P10, C8, C12, LightWriter (SL40), CEye Module Augmentative Communications Device Plate

Be the first to review this product

Availability: Out of stock

$65.00
Add Items to Cart

Quick Overview

For use with Mount'n Mover or Robo Arm wheelchair mounts.

Introduction to Device Attachment


To attach your device to the Mount'n Mover system, you will need to determine how your device can attach to the Quick Release Plate (QRP). Some devices attach directly to the QRP and others require an additional device specific attachment plate.

Device Attachment Guide

 

Tobii / ATI Devices

Plate Specific Instructions: Tobii Device Plate (DP-T1)

Brand Device Device Plate Needed QRP Hole Set Screws Required*
Tobii P10 DP-T1 Fig. 5 (4x) M4-.7 x 10mm Flat Head
C8
C12
CEye Fig. 10
LightWriter Fig. 5
QRP attachment hole set
quick release plate   device attachment figure 5   device attachment figure 10

 

Tobii ATI - S32 Device

The back of your device should look like this:
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Attach the DP-T1


Loosely attach the DP-T1 using:
  • four M4x.7 x 10mm flat head screws
    (these are the shorter screws in the bag)
Once all screws are threaded, tighten them down to torque.

Step 2: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws

Tobii ATI - C8 Device

The back of your device should look like this:

Device is shown without batteries
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Remove the "Kick-stand" Plate


Remove the "Kick-stand" Plate on the rear using a Torx T-10 bit or screwdriver.
Alternatively, you could use a 3mm Hex Key if a T-10 is not available.

Step 2: Place aluminum spacers over the mounting holes


Place the aluminum spacer sleeves over the "Kick-stand" Plate mounting holes.
  • four aluminum spacers

Step 3: Attach the DP-T1


Loosely attach the DP-T1 using:
  • four M4x.7 x 25mm flat head screws
(these are the longer screws in the bag)
Once all screws are threaded, tighten them down to torque.

Step 4: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws

 

Tobii ATI - C12-CEye Device

The back of your device should look like this:

Device is shown without batteries
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Remove the "Kick-stand" Plate


Remove the "Kick-stand" Plate on the rear using a Torx T-10 bit or screwdriver.
Alternatively, you could use a 3mm Hex Key if a T-10 is not available.

Step 2: Place aluminum spacers over the mounting holes


Place the aluminum spacer sleeves over the "Kick-stand" Plate mounting holes.
  • four aluminum spacers

Step 3: Attach the DP-T1


Loosely attach the DP-T1 using:
  • four M4x.7 x 25mm flat head screws
(these are the longer screws in the bag)
Once all screws are threaded, tighten them down to torque.

Step 4: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws

 

Tobii ATI - C15-CEye Device

The back of your device should look like this:

Device is shown without the CEye bar
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Remove the "Kick-stand" Plate


Remove the "Kick-stand" Plate on the rear using a Torx T-10 bit or screwdriver.
Alternatively, you could use a 3mm Hex Key if a T-10 is not available.

Step 2: Place aluminum spacers over the mounting holes


Place the aluminum spacer sleeves over the "Kick-stand" Plate mounting holes.
  • four aluminum spacers

Step 3: Attach the DP-T1


Loosely attach the DP-T1 using:
  • four M4x.7 x 25mm flat head screws
(these are the longer screws in the bag)
Once all screws are threaded, tighten them down to torque.

Step 4: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws
For this device you might consideradditional rotational adjustment with our Universal Rotator

 

 

Toby Churchill - Lightwriter SL40

The back of your device should look like this:
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Attach the DP-T1


Loosely attach the DP-T1 using:
  • four M4x.7 x 10mm flat head screws
(these are the shorter screws in the bag)
Once all screws are threaded, tighten them down to torque.

Step 2: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws

Tobii ATI - P10 Device

The back of your device should look like this:

This picture shows the P10 with the Daessy attachment plate
Plate needed: Device Plate T1 (DP-T1)

DP-T1 : Rev 3



Step 1: Attach the DP-T1


Remove existing mount-plate (if applicable)
Loosely attach the DP-T1 using:
  • four M4x.7 x 10mm flat head screws
Once all screws are threaded, tighten them down to torque.

Step 2: Attach the QRP


Attach the Quick Release Plate using the four short screws.
  • four #8-32 x ¼" flat head screws

 

Done!

You are now ready to use your device with the Mount"n Mover!

 

If this does not match your device, please let us know.  We want to help.

Outdoor Answers
Sort by
Most Recent Questions
Expand all
Tell us what you think about this item!

Specifications

SKU MtM0905.p
Weight 1.0000
Free Ground Shipping No
Flat Shipping Rate No
Includes No
Brand Broadened Horizons
Product Label No
Dimensions No
Warranty 1 Year
Availability Special Order - 1-3 Weeks
Shipped from Partner Warehouse Yes
Harmonization Code No
Barcode No
By Disability or Limitation No
by Ability or Control Method No

You may also be interested in the following product(s)

Mount'n Mover Custom Configurator

Mount'n Mover Custom Configurator

From: $20.00

To: $11,650.07

     

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

  Loading...